Figure Probe Connectors 1. To ensure that the ports are not active, place the system in the image freeze condition. To connect a probe: 1.
Place the probes carrying case on a stable surface and open the case. Carefully remove the probe and unwrap the probe cord. DO NOT allow the probe head to hang free. Impact to the probe head could Use the cable hooks located below the operator panel. Activating the Probe To activate the probe, select the appropriate probe from the probe indicators on the Touch Panel.
Probe Indicators 1. Probe Indicators The probes default settings for the mode and selected However, the probe should not be active when disconnecting the probe. Ensure the probe is deactivated. Deactivate by selecting another probe or pressing Freeze. Move the probe locking handle to the left.
Pull the probe and connector straight out of the probe port. Carefully slide the probe and connector away from the probe port and around the right side Press Patient. Press New Patient on the Patient menu. If there are images on the clipboard, a pop-up menu appears.
Specify whether you want to store images permanently, delete images, or go to active images. Choose the exam category. Verify the dataflow. NOTE: The system can display a warning Trace Sensitivity Adjust the trace to follow the waveform for signal strength. Page 95 Activates the menu to select which calculations are automatically calculated. Auto Calcs Activates the calculation automatically which you select in the Modify Auto Calculation when the system is in a state of freeze or live.
Page 3D Mode 6. To complete the 3D scan, press End Trackball key. Page Other Controls To zoom an image, adjust Zoom. A reference image appears in the lower, left-hand section of the display. To exit zoom, adjust Zoom until the reference zoom image is removed or press B-Mode. Page 98 but not from the worksheet.
Press Freeze. Move the Trackball. Page 99 Clear key. Press Set on the keyboard or Scan on the Touch Panel to exit without erasing the body pattern. Page To create a Fast Key, press the F5 key and follow the on-screen prompts. To start a Fast Key, press the F6 key and follow the on-screen prompts. Page 5. Thumbnail Size 3.
Page Measurement And Analysis The user should consider contraindications for the use of a calculation or chart as described in the scientific literature. The diagnosis, decision for further examination, and medical treatment must be performed by qualified personnel following good clinical practice.
Current functionality is displayed on the lower-right corner of the monitor. Pointer Key. Select to display a pointer on the monitor. Page To rotate through and activate previously fixed calipers, adjust Cursor Select. Page To erase the ellipse and the current data measured, press Clear once.
The original caliper is displayed to restart the measurement. To trace the measurement area, move the Trackball around the anatomy. A dotted line shows the traced area. To complete the measurement, press Set. The system displays the circumference and the area in the Results Window.
Page Trackball or adjust the Ellipse control counterclockwise. Page Spline trace is not available through the factory default. The system defaults to trace. Page If there are less than three points, the spline trace is removed. Press Set again. All points are removed from the trace and the trace is shown as yellow. Page Doppler Mode Measurements 2. To position the caliper at the desired measurement point, move the Trackball.
The system displays the velocity measurement in the Results Window. Page If the maximum velocity is not the maximum power, the system may not trace accurately. If you want to use maximum velocity, select either Above or Below. Page 4. To position the second caliper at the end point, move the Trackball. The system displays the time interval between the two calipers in the Results Window.
Page M-Mode Measurements 4. To position the second caliper at the most posterior point you want to measure, move the Trackball. The system displays the vertical distance between the two points in the Results Window.
The system displays time s and slope between the two points in the Results Window. Page If a worksheet has more data on a second page, to view the next page, adjust the Page Change control. Page To type a comment on a worksheet: 1. Type comments about the exam. Page To easily see which fields you can change or select, move the Trackball.
As the cursor moves over a field that you can change or select, the field is highlighted. Page 1. When the Worksheet is displayed on the monitor, press the Clear key; the following warning message appears: Figure Delete All Warning Message 2. Select OK to delete all. Select Cancel to cancel the deletion. Page Clinical Measurement Accuracy not the full scale range. Where the accuracy is stated as a percent with a fixed value, the expected inaccuracy is the greater of the two. Page Probe Cleaning Process 3.
Rinse the probe with enough clean potable water to remove all visible soap residue. Air dry or dry with a soft cloth. Probe Immersion Levels 1. Page Since there is a possibility of having negative effects on the probe, observe the specified immersing time by the germicide manufacturer strictly.
Do not immerse the probe in liquid chemical germicides more than the time prescribed in the care card. Page Thoroughly clean the probe, as described earlier before attempting disinfection. Failure to do so could damage the system. Do not use a damaged or defective probe.
Refer to the Trophon EPR user documentation for more information on disinfecting approved probes. This could cause permanent damage to the probe. Remove the probe from the Trophon EPR. Wipe the probe prior to use with an absorbent, single-use, dry, lint-free cloth.
Remove and discard the disposable gloves. Page Coupling Gels Do not apply gel to the eyes. Page Ensure you always use sterile ultrasound gel for those procedures that require sterile ultrasound gel. Once a container of sterile ultrasound gel is opened, it is no longer sterile and contamination during subsequent use is possible.
Page Figure Press Regional Options. Press Apply. Press OK. Set Language 5. Change system locale 7. Change the setting to English. Russian Keyboard Here is an example of the Greek keyboard: Figure Page Daily backup is recommended. External storage media is recommended for image archive.
Page If you uncheck this option, the system only backs up exams which have not yet been backed up. NOTE: If you update an exam which is already backed up, the exam is also backed up. Page However, take care not to import studies over existing studies; duplicate or missing images may result.
Delete the existing exam first. Select Backup. The system performs the backup. After the backup is complete, press F3 to eject the CD. Page Restore Procedure: Patient Data 5. In the Restore list, select Patient Archive. In the Media field, select the media.
Select Restore. The system performs the restore. Page Configuring Connectivity You use Connectivity functionality to set up the connection and communication protocols for the ultrasound system. The following page gives an overview of each of the Connectivity functions. Each function is described in detail in the following pages. Page Connectivity Functions The ultrasound system is pre-configured for many services, with default settings selected.
You can change these services and settings as needed. The LOGIQ E9 Ultrasound system is designed with you, your specialty, and your patients in mind offering extraordinary image quality, easy workflow, and expert tools to help you provide the best patient care.
Woloska Page Manufacturer U. Page Inspecting The System If any defects are observed or malfunctions occur, do not Electrical operate the equipment but inform a qualified service person. Hazard Contact a Service Representative for information. Wipe down the top, front, back, and both sides of the Touch Panel.
Wipe off excess cleaning agents. Page 3. Wipe down operator control panel. Use a cotton swab to clean around keys or controls. Use a toothpick to remove solids from between keys and controls. Page Footswitch To clean the footswitch: 1.
Moisten a soft, non-abrasive folded cloth with a mild, general purpose, non-abrasive soap and water solution.
Position your other hand at a corner of the filter and wedge a finger between the filter and the bottom of the LOGIQ E9. Pull down on the filter with the finger that is wedged Page Assistance Not all features or products described in this document may be available or cleared for sale in all markets. Contact the distributor, GE affiliate or sales representative for approved peripherals. For HCATs, contact your sales person. Because the availability of these agents is subject to government regulation and approval, product features intended for use with these agents may not be commercially marketed nor made available before the contrast agent is cleared for use.
Page Chapter 4 Safety Describes the safety and regulatory information pertinent for operating this ultrasound system. Page Owner Responsibility It is advisable to maintain a list of authorized operators.
Should the system fail to operate correctly, or if the unit does not respond to the commands described in this manual, the operator should contact the nearest field GE Ultrasound Service Office. For information about specific requirements and regulations applicable to the use of electronic medical equipment, consult the local, state and federal agencies.
Page Notice Against User Modification Notice against user modification Never modify this product, including system components, software, cables, and so on.
User modification may cause safety hazards and degradation in system performance. All modification must be done by a GE qualified person.
Page The user must be thoroughly familiar with the instructions and potential hazards involving ultrasound examination before attempting to use the device. Training assistance is available from GE Healthcare if needed.
Disregarding information on safety is considered abnormal use. The use of the system outside the described conditions or Page Patient Safety It is advisable to back up system data prior to any service repairs to the hard drive. It is always possible during system failure and repair to lose patient data. GE will not be held responsible for the loss of this data. Page The user should be aware of the product specifications and of the system accuracy and stability limitations. These limitations must be considered before making any decision based on quantitative values.
Equipment malfunction or incorrect settings can result in measurement errors or failure to detect details within the image.
Page A damaged housing, lens or cable can result in patient injury or serious impairment or operation. Do not use with Defibrillator. Page It is recommended that all users receive proper training in applications before performing them in a clinical setting. Please contact the local GE representative for training assistance. Spilled liquid may contact live parts and increase the risk of shock.
GE is NOT responsible for any lost patient information or for lost images. Use a USB printer cable that is less than 3 meters in length. Page Sensitive users and patients must avoid contact with these items. Page Service Representative for information.
Page Emc Electromagnetic Compatibility Use of cables not properly shielded and grounded may result in the equipment causing radio frequency interference in violation of the FCC regulations. Page Do not use devices which intentionally transmit RF Signals cellular phones, transceivers, or radio controlled products other than those supplied by GE wireless microphone, broadband over power lines, for example in the vicinity of the equipment as it may cause performance outside the published specifications.
Page Do not use devices which intentionally transmit RF signals CAUTION cellular phones, transceivers, or radio controlled products , other than those supplied by GE wireless microphone, broadband over power lines, for example unless intended for use with this system, in the vicinity of this equipment as it may cause performance outside the published specifications.
Page RF shielded examination room may be necessary. Products equipped with a power source plug should be plugged into the fixed power socket which has the protective grounding conductor. Operate the system with all covers closed. Operating the system with any cover open may affect EMC performance. A Wireless LAN option is available. Page IEC Everyone who connects additional equipment to the signal input part or signal output part of the LOGIQ E9 system configures a medical system, and is therefore responsible to ensure that the system complies with the requirements of the valid version of IEC If in doubt, consult the technical service department or your local GE Healthcare representative.
Equipment modifications and possible resulting malfunctions and electromagnetic interference are the responsibility of the owner. Page This system is suitable for use in the following environment.
The user must assure that the system is used according to the specified guidance and only in the electromagnetic environment listed. Good power line isolation is required. Page Patient Environmental Devices 3. IEC standard or equivalent standards appropriate to devices. Used when bone is near the skin surface as in transcranial examination, it provides an estimate of potential temperature increase in the bone or adjacent soft tissue.
Always observe the Acoustic Output display for possible effects.
0コメント